Armadillo Safes

NMXi/NMX

Your safe has the ability to store up to 20 unique authorized users. A user consists of 5 scans of the same finger during programming. Follow the “Program Fingerprints” section below to get started.

Your safe supports Nano Key the fastest access available. Its small footprint and mountable base make it easy to hide and conceal anywhere, making it suitable for use as a panic button. Take caution when using the included VSK-N Nano Key and be responsible. Security can be compromised in the event it is lost or stolen. Only pair VSK-N Nano Key after thoroughly understanding the inherent risks.

IMPORTANT: VSK-N Nano Key is compatible with VT Series (VT/VTi), MX Series (MX/MXi/NMX/NMXi), Slider Series (SL20/SL20i/NSL20/NSL20i) and RS Series (RS200i/RS500i).

NEW! Sold separately is the new VSK-NT Nano Key Biometric which features a fingerprint scanner for secure and discreet access to your safe.

Toggle Alert of Manual Unlock: If the Alert of Unlock is on, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing. To toggle Alert Unlock press and hold keys ‘3’ and ‘6’ then “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF.

Tamper Detection: To check for tampering press and hold keys ‘2’ and ‘4’ together for 3 seconds. The screen will indicate TAMPERING or CLEARED. You can reset the tamper detection by opening the safe through one of the authorized entry points.

Toggle Sound: To toggle the sound ON/OFF press and hold keys ‘1’ and ‘3’ together for 3 seconds. The screen will indicate the sound is ON and beep or the screen will indicate OFF and not beep.

Toggle Travel Mode: Save battery life by disabling the proximity sensor, keypad, and status bar. To toggle travel mode ON/OFF press and hold keys ‘1’ and ‘8’ together for 3 seconds. The screen will indicate ENABLED or DISABLED.

View Battery Status: To check the battery level press and hold keys ‘6’ and ‘8’ together for 3 seconds. The screen will indicate the battery level. See pages 08 to 09 for more information.

Toggle Open Door Alarm: Your safe features an open door alarm that will sound when the safe door is left open for more than 8 minutes. By default, this alarm is ON. To toggle off press and hold keys ‘3’ and ‘5’ and “PROGRAM” together (3 seconds). The screen will indicate ON or OFF.

Toggle Interior LED Light: To toggle the interior light ON/OFF press and hold keys ‘5’ and ‘7’ together 3 seconds. With the light toggled to ON you can press the “LIGHT” button inside the safe to illuminate the light and can also adjust brightness in the app. If the light is toggled OFF the light will be disabled.

Adjust LCD Brightness The LCD screen has four brightness levels: 25%, 50%, 75%, and 100%. To toggle the LCD brightness press and hold ‘5’ and ‘8’ together for 3 seconds. The screen will indicate the brightness level.

Toggle Smart Key Entry Modes: The Smart Key has THREE modes: OFF, Progressive Entry Mode, and On Demand Entry Mode. OFF disables Smart Key access. Progressive Entry Mode requires that you press one key on the safe keypad first and then activate the Smart Key. On Demand Entry Mode grants immediate access when activating the Smart Key. Pressing and holding the ‘6’ key then “PROGRAM” button together for 3 seconds will allow you to toggle through each mode from the keypad. You may also alternate modes in the Vaultek® app.

Adjust DMT Sensitivity (Impact Detection): Your Vaultek® safe has a built-in accelerometer and corresponding alarm that alerts of any attacking to your safe including bumps and impacts, DMT (Impact Detection). DMT is enabled by default and its sensitivity has three settings; Low, Medium, and High. You can toggle through these settings by pressing and holding the ‘7’ key then “PROGRAM” button together for 3 seconds. The screen will indicate LOW, MEDIUM, and HIGH as well as DISABLED.

Factory Reset: Press keys ‘2’ and ‘7’ and PROGRAM together 3 seconds. IMPORTANT The Factory Reset erases ALL programmed information and restores the safe to its default settings. This includes any enrolled fingerprints and master code. The master code is reset to 1-2-3-4 and the safe will restart. The safe will need to be configured again to work with the Vaultek® WiFi® smartphone app and Web Dashboard.

View Temperature/Humidity: Your Vaultek® safe has built in sensors to monitor the internal temperature as well as the relative humidity inside your safe. Press keys ‘2’ and ‘5’ together to display the information on your safe’s LCD screen. You can also monitor the safe’s temperature and humidity from the Vaultek® Wi-Fi® smartphone app and online Web Dashboard. You even have the option to set thresholds and be alerted of any significant changes.

Toggle Fahrenheit/Celsius: By default, the safe will measure temperature in Fahrenheit. By pressing keys ‘2’ and ‘6’ together you can toggle the display to show temperature in either Fahrenheit or Celsius.

NMXi Only

Delete Fingerprints: To delete fingerprints press and hold the ‘3’ key then “PROGRAM” button together until the safe beeps and the screen prompts you to enter your master code. Enter your master code on the keypad. If the code is correct, the safe will beep and the screen will indicate deletion of all the fingerprints. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek® app.

Toggle Dual Entry Mode: To toggle the Dual Entry ON/OFF press and hold the ‘8’ key then “PROGRAM” button together for 3 seconds. The screen will indicate ENABLED or DISABLED. If the Dual Entry is toggled ON, you will be required to enter your master code and fingerprint (and vice versa) to open the safe. This mode requires that at least one fingerprint be programmed in the safe.

Check and see what the app is showing in the failed to connect dialog box and which error is showing.

Timed out while waiting to pair to the safe/Error Code 1

The safe failed to pair on the server before the timeout. Could be that the safe did not connect to the network or the app failed to connect to its previous network during the process. If the safe showed “Connected” and beeped with a green light, but not letting you access the app dashboard, use the “add a user” button to connect.

Failed to open a socket to the safe. Please try again/Error Code 2

All attempts to create a direct connection to the safe to send the Wi-Fi information failed. For some phones this may happen do to the low quality of the phone’s Wi-Fi chip. Close the dialog and attempt the connection process again.

Safe failed to return a response/Error Code 3

The Wi-Fi network information was sent to the safe but the safe never returned any indication that it was received. Attempt to connect again.

The safe failed to connect to the network/Error Code 4

This usually indicates that the safe was not able to connect to the Wi-Fi network. There are several reasons why this could happen:

• The Wi-Fi signal is poor, resulting in the safe taking too long to try to connect to it.

The network name is wrong, if you manually entered in the network name during step 1 it may have been mistyped. Network names are CASE SENSITIVE. Check the network name spelling and try again.
The password was wrong or the password may have been entered wrong. The password is also CASE SENSITIVE. Check the password spelling and try again.
The router is blocking the connection, some AT&T Uverse routers may block the safe from connecting. Unplug the router for 10 seconds and plug it back in and try again after it is done connecting to the provider services.
The phone failed to connect to stable Internet. After sending connection data to the safe, your phone will disconnect and attempt to re-connect to the strongest configured network. If the phone fails to do this, or connects to a bad network the app will not be able to complete the connection. Usually if the safe indicates a connection is made but the app does not, this is the problem. You can try to pair to the safe with the “Add a User” button if the safe was able to get online.

Nothing or bad data was sent from the safe/Error Code 5

The safe received the Wi-Fi network information but replied back with missing information. Attempt the connection again.

Timed out while attempting to connect to the safe/Error Code 6

All attempts to create a direct connection to the safe to send the Wi-Fi information failed. For some phones this may happen do to the low quality of the phone’s Wi-Fi chip. Close the dialog and attempt the connection process again.

Timed out while waiting for a response from the safe/Error Code 7

The app sent the Wi-Fi connection information but timed out while waiting for the safe to confirm it received it. Close the dialog and attempt the connection process again.

Maximum number of users has been reached for this safe/Error Code 8

The safe already has one user paired to it. Currently, only one user can pair to each safe at a time.

MXi/MX

TIP: Place the core of the fingerprint flat (Figure E+F) over the center of the scanner in line with the side LEDs (this allows the scanner to read where most of the fingerprint detail is located) see (Figure E).

TIP: Adjust your finger slightly between scans for increased accuracy.

TIP: Excessive moisture, lotions, or dirt will affect your fingerprint and may cause inaccurate sensor reading.

TIP: If you are having difficulty with your print, program the same finger 4 or 5 times. You have 20 slots available for programing and you can also try your thumb as it has more surface area to read.

NMX / NMXi

After the first two Admin fingerprints have been locked in, you can add additional users or fingerprints, up to 20 unique users in total. This is very helpful in the event the fingerprint scanner is having a hard time reading your initial fingerprints, or if you wish to grant other users authorized access to your safe. Any additional users programmed require authorization from one of the two Admin fingerprints.

1) Open the safe. Program additional fingerprints by pressing and holding the ‘2’ then “PROGRAM” button together (3 seconds). The screen will prompt you to scan one of the administrative fingerprints.

2) Place one of the first two programmed administrative fingerprints on the scanner and remove when the safe beeps and screen authorizes the print. You can now program a NEW fingerprint.

TIP: If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the safe again and not the NEW fingerprint. If this happens start over with step 1.

3) Using the helpful programming tips provided on page 09 place the NEW finger on the scanner. When the safe beeps and the screen prompts the next scan remove your finger.

4) Place finger again over the scanner until the safe beeps and the screen prompts the next scan and lift. You will repeat this process until all scans (1-5) are programmed.

MX / MXi

After the first two Admin fingerprints have been locked in, you can add additional users or fingerprints, up to 20 unique users in total. This is very helpful in the event the fingerprint scanner is having a hard time reading your initial fingerprints, or if you wish to grant other users authorized access to your safe. Any additional users programmed require authorization from one of the two Admin fingerprints.

1) Open the safe. Program additional fingerprints by pressing and holding the ‘2’ then “PROGRAM” button together (3 seconds). The screen will prompt you to scan one of the administrative fingerprints.

2) Place one of the first two programmed administrative fingerprints on the scanner and remove when the safe beeps and screen authorizes the print. You can now program a NEW fingerprint.

TIP: If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the safe again and not the NEW fingerprint. If this happens start over with step 1.

3) Using the helpful programming tips provided on page 11 place the NEW finger on the scanner. When the safe beeps and the screen prompts the next scan remove your finger.

4) Place finger again over the scanner until the safe beeps and the screen prompts the next scan and lift. You will repeat this process until all scans (1-5) are programmed.

Get the App: Download the Vaultek® Bluetooth app from the Google Play store or Apple store.

1) Make sure your phone’s Bluetooth settings are set to ON, and open the Vaultek® Bluetooth app to begin.

IMPORTANT: You must be within Bluetooth range to pair your phone with your safe. The approximate range is 25 feet.

2) Create a Pattern Lock: This is an added layer of protection to safeguard your safe and prevent unauthorized access in the event your phone is misplaced. To create your pattern lock, simply drag your finger along the screen to connect at least four dots. This unique pattern will be required each time you open the app.

3) Select Your Safe: After a few seconds your safe will appear in the search. You can drag the screen downwards to refresh if you are not seeing your safe listed. Select your safe, and enter your safe’s master code when prompted. This is the same code used to open the safe using the numeric keypad.

IMPORTANT: If you change your safe’s master code after pairing, the safe will no longer connect to your app, and you will be prompted to enter the new code when needed.

IMPORTANT: As a security measure, if too many incorrect master code entries are entered, your safe’s Bluetooth will disable and must be toggled ON again using the hot key sequence.

4) Sync Your Phone: Press and hold keys ‘4’ and ‘5’ on your safe followed by the PROGRAM button together for 3 seconds to start the syncing protocol. When the keypad starts blinking red you can finalize the pairing sequence from your app screen by pressing ‘OK’. The safe’s keypad will flash green and beep when complete, if the keypad flashes red with two beeps you will need start over with step 4.

TIP: This pairing sequence offers enhanced security protection and can only be used to pair one phone to your safe. If the process is repeated with a different phone, the previous phone will be overridden and disconnected from the safe.

Nano Key allows for the fastest access available into your safe. Please use responsibly.

NMX / NMXi

IMPORTANT: Be sure to follow ALL steps for proper function.

1) Press and hold the ‘5’ key then “PROGRAM” button together (3 seconds) until the LCD screen indicates CONNECTING.

2) Aim Nano Key towards the safe and press. If the safe beeps and the screen indicates COMPLETE then the Nano Key has paired successfully. If the screen indicates FAILED TO PAIR then simply start over with step 1.

IMPORTANT: Set Entry Mode: After pairing, Nano Key will be immediately active to test functionality, but then deactivate. Nano Key settings will need to be set to either On Demand or Progressive in order for Nano Key to open your safe. See next page for more information.

Multiple Safe Management

A) Multiple Nano Keys can not pair with the same safe. It is recommended to pair one Nano Key per safe.

B) Recommended setting when using the Nano Key is Progressive entry mode.

C) You can manage multiple safes through the Vaultek® Wi-Fi® smartphone app and Web Dashboard.

CAUTION: when managing multiple safes in On Demand entry mode there is a chance you can open all safes within range.

MX / MXi

Your Vaultek® safe supports quick access with Nano Key technology. Nano Key is not included but can be purchased separately at www.vaulteksafe.com or from one of our authorized dealers. Take caution when using this feature and be responsible. Security can be compromised in the event the Nano Key is lost or stolen. Only pair Nano Key after thoroughly understanding the inherent risks.

IMPORTANT: Be sure to follow ALL steps for proper function.

1) Press and hold the ‘5’ key then “PROGRAM” button
together (3 seconds) until the LED flashes RED and the screen indicates connecting.

2) Aim Nano Key towards the safe and press. If the safe beeps and the screen indicates complete then the Smart Key has paired successfully; if the screen indicates failed to pair then simply start over with step 1.

IMPORTANT: Set Entry Mode: After pairing, Nano Key will be immediately active to test functionality, but then deactivate. Nano Key settings will need to be set to either On Demand or Progressive in order for Nano Key to open your safe. See next page for more information.

Multiple Safe Management

A) Multiple Nano Keys can not pair with the same safe. It is recommended to pair one Nano Key per safe.

B) Recommended setting when using the Nano Key is Progressive entry mode.

C) You can manage multiple safes through the Vaultek® Bluetooth® smartphone app and Web Dashboard.

CAUTION: when managing multiple safes in On Demand entry mode there is a chance you can open all safes within range.

NMX / NMXi

After pairing you can toggle between access modes from the keypad, Wi-Fi® smartphone app, or the online Web Dashboard. To toggle modes from the safe’s keypad press and hold the ‘6’ key then “PROGRAM” button together until the LCD screen indicates each mode as below.

Off – Keys Turn Solid RED

Progressive Entry Mode – Keys Blink Green
Safe goes into sleep mode and will require you to wake up the safe before using Smart Key. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED).

On Demand Entry Mode – Keys Solid Green
This mode grants immediate access to your safe without having to wake it up.

Warning: On Demand Entry Mode can open a safe in another room and/or out of sight. To reduce the risk of an unattended open safe we recommend using Progressive Entry Mode.

On Demand Entry mode requires significant power usage and can greatly reduce operation time. We suggest setting the Smart Key to Progressive Entry Mode to conserve battery.

MX / MXi

After pairing you can toggle between access modes from the keypad or Bluetooth® smartphone app. To toggle from the keypad press and hold the ‘6’ key then “PROGRAM” button together. The LCD screen will communicate as directed below.

Off – Keys Turn Solid RED

Progressive Entry Mode – Keys Blink Green
Safe goes into sleep mode and will require you to wake up the safe before using Smart Key. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED).

On Demand Entry Mode – Keys Solid Green
This mode grants immediate access to your safe without having to wake it up.

Warning: On Demand Entry Mode can open a safe in another room and/or out of sight. To reduce the risk of an unattended open safe we recommend using Progressive Entry Mode.

On Demand Entry mode requires significant power usage and can greatly reduce operation time. We suggest setting the Smart Key to Progressive Entry Mode to conserve battery.

Toggle Alert of Manual Unlock: If the Alert of Unlock is on, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing. To toggle Alert Unlock press and hold keys ‘3’ and ‘6’ then “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF.

Tamper Detection: To check for tampering press and hold keys ‘2’ and ‘4’ together for 3 seconds. The screen will indicate TAMPERING or CLEARED. You can reset the tamper detection by opening the safe through one of the authorized entry points.

Toggle Sound: To toggle the sound ON/OFF press and hold keys ‘1’ and ‘3’ together for 3 seconds. The screen will indicate the sound is ON and beep or the screen will indicate OFF and not beep.

Toggle Travel Mode: Save battery life by disabling the proximity sensor, keypad, and status bar. To toggle travel mode ON/OFF press and hold keys ‘1’ and ‘8’ together for 3 seconds. The screen will indicate ENABLED or DISABLED.

View Battery Status: To check the battery level press and hold keys ‘6’ and ‘8’ together for 3 seconds. The screen will indicate the battery level. See pages 08 to 09 for more information.

Toggle Open Door Alarm: Your safe features an open door alarm that will sound when the safe door is left open for more than 8 minutes. By default, this alarm is ON. To toggle off press and hold keys ‘3’ and ‘5’ and “PROGRAM” together (3 seconds). The screen will indicate ON or OFF.

Toggle Interior LED Light: To toggle the interior light ON/OFF press and hold keys ‘5’ and ‘7’ together 3 seconds. With the light toggled to ON you can press the “LIGHT” button inside the safe to illuminate the light and can also adjust brightness in the app. If the light is toggled OFF the light will be disabled.

Adjust LCD Brightness The LCD screen has four brightness levels: 25%, 50%, 75%, and 100%. To toggle the LCD brightness press and hold ‘5’ and ‘8’ together for 3 seconds. The screen will indicate the brightness level.

Toggle Smart Key Entry Modes: The Smart Key has THREE modes: OFF, Progressive Entry Mode, and On Demand Entry Mode. OFF disables Smart Key access. Progressive Entry Mode requires that you press one key on the safe keypad first and then activate the Smart Key. On Demand Entry Mode grants immediate access when activating the Smart Key. Pressing and holding the ‘6’ key then “PROGRAM” button together for 3 seconds will allow you to toggle through each mode from the keypad. You may also alternate modes in the Vaultek® app.

Adjust DMT Sensitivity (Impact Detection): Your Vaultek® safe has a built-in accelerometer and corresponding alarm that alerts of any attacking to your safe including bumps and impacts, DMT (Impact Detection). DMT is enabled by default and its sensitivity has three settings; Low, Medium, and High. You can toggle through these settings by pressing and holding the ‘7’ key then “PROGRAM” button together for 3 seconds. The screen will indicate LOW, MEDIUM, and HIGH as well as DISABLED.

Factory Reset: Press keys ‘2’ and ‘7’ and PROGRAM together 3 seconds. IMPORTANT The Factory Reset erases ALL programmed information and restores the safe to its default settings. This includes any enrolled fingerprints and master code. The master code is reset to 1-2-3-4 and the safe will restart. The safe will need to be configured again to work with the Vaultek® Bluetooth® app.
MXi Only

Delete Fingerprints: To delete fingerprints press and hold the ‘3’ key then “PROGRAM” button together until the safe beeps and the screen prompts you to enter your master code. Enter your master code on the keypad. If the code is correct, the safe will beep and the screen will indicate deletion of all the fingerprints. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek® app.

Toggle Dual Entry Mode: To toggle the Dual Entry ON/OFF press and hold the ‘8’ key then “PROGRAM” button together for 3 seconds. The screen will indicate ENABLED or DISABLED. If the Dual Entry is toggled ON, you will be required to enter your master code and fingerprint (and vice versa) to open the safe. This mode requires that at least one fingerprint be programmed in the safe.

MXE

Free Shipping

Veteran Founded

Superior Support

Price Guarantee

NMXi/NMX

MXi/MX

MXE

Search

Let customers speak for us