10 Series

NEW VS10i

Your safe is powered by a 3.7V 18650 rechargeable lithium-ion flat-top battery. A minimum 2000 mAh capacity is required, however, 2200 mAh or higher can reuse to increase operation time.

Tip! After installing the battery, use the charging kit provided to charge the unit 100%.

Battery Installation:

1) To get started, insert one of your backup keys into the keyhole at the front of the safe. Push key in and rotate the key 90 degrees clockwise to open the safe.

2) Remove the interior padding. Locate the battery compartment door on the inside of the safe directly behind the ‘1’ key on the keypad.

3) Remove the battery cover by pressing down on the tab near the top of the cover.

Insert the 18650 rechargeable lithium-ion battery (included in the accessory box) into the battery compartment. Note that your Vaultek safe automatically detects the polarity of the battery and can be installed in either direction.

Tip! Before inserting the battery make sure to place the pull string over the battery before closing the door for easy removal.

4) When the battery is inserted you will hear a short welcome tone and the keypad will light up. Once you hear the tone and see the keypad light up, replace the battery cover.

Tip! Leaving your safe plugged in continually will not harm the safe or battery. However, to preserve battery life we suggest that you unplug occasionally to allow the battery to cycle down.

Important! Your Vaultek safe will atomically lock when you fully close the lid.

Tip! Register your safe online. This is important in the event you lose your keys.

Charging the Battery:

1) To recharge the safe, plug the micro-USB into the micro-USB receiving jack located on the right side of the safe and connect to a standard USB port or wall outlet using the AC power adapter. The approximate recharge time is 2.5 hours.

2) The LED next to the receiving jack on the side of the safe will glow RED indicating charging and GREEN indicating charged.

Tip! After installing the battery, use the charging kit provided to charge the unit 100%.

Your safe can store up to 20 unique fingerprints. The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize additional users.

1) Place the core of the fingerprint flat over the center of the scanner. This allows the scanner to read where most of the fingerprint detail is located.

2) Rotate your finger slightly between registration scans to store print variations for increased accuracy.

3) Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

4) To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

Troubleshooting! If you are having difficulty with your print, program the same fingerprint 4 or 5 times. You have 20 slots available for programming and you can also try your thumb as it has more surface area to read.

Troubleshooting! If you are experiencing a low success rate. Delete the fingerprints on safe and start over.

Try the following if you are experiencing a low success rate with the fingerprint scanner. Let’s perform a soft reset of the scanner by deleting the fingerprints on the safe.

STEP 1: Perform a Soft Reset

1) Press and hold ‘1’ and “PROGRAM” buttons together for 3 seconds until all keys (1-5) light up RED then enter your master code. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek Bluetooth 2.0 app.

2) Then remove the battery and reinstall.

Now let’s try reprogramming your fingerprint using the helpful tips below.

– Place the core of the fingerprint flat over the center of the scanner. This allows the scanner to read where most of the fingerprint detail is located.

– Rotate your finger slightly between registration scans to store print variations for increased accuracy.

– Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

– To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

STEP 2: Program the First Print

Your safe can store up to 20 unique fingerprints. The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize additional users 3 to 20. Let’s enroll the first admin print in the safe.

1) Tap the “PROGRAM” button. The ring around the scanner will turn RED and the ‘1’ key on the keypad will blink RED.

2) When the 1 keys starts blinking place your finger for scan, 1, 2, 3, 4, and 5.

3) This completes enrollment for the first admin print.

Close the door and test to see if the safe will open using your fingerprint.

Tip! Repeat these steps to enroll the second admin print.

Still having issues? Please contact our support team via email at support@vaulteksafe.com.

The Vaultek Bluetooth 2.0 app lets you get the most out of your safe. Using the app gives you access and control over features that are not possible using the keypad interface alone.

Bluetooth 2.0 App Features:

– Unlock Safe Within Range (optional)

– Check Battery Level

– Adjust Sound

– Adjust Interior LED Light Duration

– Smart Key Nano 2.0 Management

– Fingerprint Management

– View History Log

Pairing Safe to the Bluetooth 2.0 App

1) Get the App. Android users can download the app from Google Play and Apple users can download from the Apple App Store. This app is different from Vaultek’s Bluetooth and WiFi app. Be sure to look for the Vaultek Bluetooth 2.0 app.

Important! Only compatible with Bluetooth 2.0 Vaultek safes. Not sure if your safe is Bluetooth 2.0? Look for the Bluetooth 2.0 icon mark on the outside of the packaging or on the safe.

Important! Make sure your Bluetooth settings in your phone are toggled ON.

Important! You must be within Bluetooth range of the safe to pair. The approximate range is 25 feet.

Tip! The initial app screens will guide your setup.

2) Open the app to begin pairing.

3) Create a pattern lock. This can be disabled later.

4) Add your safe.

5) Select your safe from the list.

6) Press and hold the 3 key and program button together for 3 seconds. When the keypad flashes green, it has been successfully paired and the buttons can be released.

Once paired to your safe you can perform a number of functions including changing the safe name, manage fingerprints, disable pattern lock, manage smart key, adjust the interior light duration, and more.

By default the unlock feature on the app will be disabled. The unlock feature will be disabled by default. If you wish to enable this feature, press and hold keys ‘1’ ‘4’ and program button together for 3 seconds. Once enabled you will be able to unlock the safe within Bluetooth range. Repeat the sequence to disable the unlock feature.

This pairing sequence offers enhanced security protection and can only be used to pair one phone to your safe. If the process is repeated with a different phone, the previous phone will be overridden and disconnected from the safe.

Note, Vaultek does not in any way access your personal data (including photos, locations, contacts, etc). The app requires permissions to store certain preferences such as safe settings and fingerprint ID names in the memory of your phone. It also uses the Bluetooth function of your phone for wireless communication with your safe.

Alert of Manual Unlock: If the Alert of Unlock is ON, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing and beep for 10 seconds. To clear the alarm you must enter the authorized master code. To toggle Alert Unlock press and hold keys ‘4’ ‘5’ and “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF.

Tamper Detection: To check for tampering press and hold keys ”2 and ‘4’ together for 3 seconds. The keys ‘3’ glow RED to indicate tampering or GREEN to indicate no tampering. The safe considers an incorrect keypad entry and unauthorized fingerprint scan (biometric model only) as tampering. You can reset the tamper detection by opening the safe through one of the authorized entry points.

Sound: Toggle between four different sound settings. High pitch, medium pitch, low pitch, and off. To toggle the sound settings press and hold keys ‘1’ and ‘3’ together for 3 seconds. If keys ‘2’ ‘4’ and ‘5’ glow GREEN, the sound is High ; if keys ‘2’ and ‘4 glow GREEN the sound is Medium ; if the ‘2” key glow GREEN the sound is low, and if the ‘2’ key glows RED the sound if off. The sound is medium by default.

Travel Mode: Save battery life by disabling the proximity sensor, fingerprint sensor, keypad, and Bluetooth 2.0 features. To toggle travel mode ON/OFF press and hold keys ‘1’ ‘3’ and ‘5’ together until the safe beeps and the keys light up. If keys ‘2’ and ‘4’ glow RED, the safe is disabled; if the keys ‘2’ and ‘4’ glow GREEN, the safe is operational.

View Battery Status: To check the battery level press and hold the ‘5’ key on the keypad for3 seconds). Keys from ‘1’ to ‘4’ will glow GREEN or RED to indicate the battery level.

If 4 keys glow green: 80%-100%

If 3 keys glow green: 60%-80%

If 2 keys glow green: 40% – 60%

If 1 key glows green: 20%-40%

If 1 key glows red: 10%-20%

If 1 key blinks red: less than 10%

Low Battery Alarm: Your safe features a low battery alarm that will sound when the safe is low in battery, and will sound continually every 8 minutes until the battery dies. To toggle press and hold keys ‘1’ ‘2’ and “PROGRAM” button together for 3 seconds. If the keypad flashes RED, the alarm is disabled; if the keypad flashes GREEN, the alarm is enabled. The alarm is ON by default.

Interior Light: Select the desired duration the interior light is ON for. To toggle the interior light settings press and hold the ‘1’ key for 3 seconds.The keypad will indicate the selection as below:

Off: Keys (1-5) glow RED

Interior Light ON for 10 seconds: Key ‘2’ Green

Interior Light ON for 30 seconds: Keys ‘2’ and ‘4’ Green

Interior Light ON for 60 seconds: Keys ‘2’ ‘3’ and ‘4’ Green

If the light times out, press the “LIGHT” button inside the safe to extend the light for additional time as needed. You can also adjust the settings in the Vaultek Bluetooth 2.0 app. If the light is toggled OFF the light will be disabled.

Bluetooth 2.0 App Unlock: By default, the unlock feature on your app will be disabled. If you wish to enable this feature, press and hold keys ‘1’ and ‘4’ followed by the PROGRAM button together for 3 seconds. Repeat the sequence to disable the unlock feature.

Dual Entry Mode (Only VS20i): Once enabled the safe requires input of the master code and enrolled fingerprint or vice versa to open the safe. To toggled ON/OFF press and hold keys ‘3’ ‘4’ and “PROGRAM” button together for 3 seconds. If the keypad flashes RED the feature is OFF, if the keypad flashes GREEN the feature is ON. This mode requires that at least one fingerprint be programmed in the safe.

Delete Fingerprints (Only VS20i): Individual fingerprints cannot be deleted from the keypad on the safe. Following this procedure will erase all the fingerprints including both administrative fingerprints. Individual fingerprints can be deleted from the Vaultek Bluetooth 2.0 app. Press and hold ‘1′ and “PROGRAM” button together for 3 seconds until all keys (1-5) light up RED then enter your master code. This will remove all the fingerprints.

Factory Reset: The Factory Reset erases all programmed information and restores the safe to its default settings. This includes removing any enrolled fingerprints and resetting the master code to 1-2-3-4-5. The safe will need to be reconfigured again to work with the Vaultek Bluetooth 2.0 app. To perform a factory rest, press and hold keys ‘1’ and ‘5’ and “PROGRAM” button together until the keypad flashes green and the safe restarts. Once the safe restarts remove the battery from the safe, and then put the battery back.

Your safe supports quick access with Nano Key 2.0. Nano Key 2.0 is not included but can be purchased separately. Nano Key 2.0, part of Vaultek’s line of Nano Keys, provides instant access to your safe in the event you need immediate entry. It’s small footprint and mountable base make it easy to hide and conceal anywhere, making it suitable for us as a panic button.

Take caution when using this feature and be responsible. Security can be compromised in the event Nano Key is lost or stolen. Only pair Nano Key after thoroughly understanding the inherent risks.

– Avoid unintentional safe open, Nano Key should only be used when the safe is in sight.

– WARNING anyone including children can access the safe with Nano Key.

– ALWAYS unpair Nano Key in the event it is lost or stolen. Refer to the unpairing steps.

VT10i/VT10

Your safe can store up to 20 unique fingerprints. The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize additional users (3-20). Please refer to “Programming Admin Fingerprints” to get started.

1. Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).

2. Rotate your finger slightly during registration scans.

Your safe can store up to 20 unique fingerprints. The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize additional users 3 to 20.

Fingerprint TIPS!

1. Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).

2. Rotate your finger slightly during registration scans.

Programming Admin Print 1 of 2

1) Open the safe. Program the 1st fingerprint by quickly pressing “PROGRAM”. The light above the fingerprint scanner will turn solid RED and the ‘1’ key on the keypad will start blinking RED.

TIP: If all keys are blinking RED and the light above the fingerprint scanner turns solid RED then refer to the programming fingerprints 3-20 below.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the ‘1’ key lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the ‘2’ key lights up GREEN and lift. You will repeat this process until all keys (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.

TIP! Repeat these steps to program the second admin print.

Programming Admin Print 2 of 2

1) Open the safe. Program the 1st fingerprint by quickly pressing “PROGRAM”. The light above the fingerprint scanner will turn solid RED and the ‘1’ key on the keypad will start blinking RED.

TIP: If all keys are blinking RED and the light above the fingerprint scanner turns solid RED then refer to the programming fingerprints 3-20 below.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the ‘1’ key lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the ‘2’ key lights up GREEN and lift. You will repeat this process until all keys (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.

IMPORTANT! Once both admin prints are enrolled you can program additional prints. Your safe can store up to 20 unique fingerprints. To program addition prints refer to “Program Additional Prints”.

Try the following if you are experiencing a low success rate with the fingerprint scanner.

Let’s perform a soft reset of the scanner by deleting the fingerprints on the safe. Press and hold keys ‘3’ and ‘5’ at the same time for 3 seconds until all keys (1-5) light up RED then enter your master code. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek Bluetooth app. Then remove the battery and reinstall. Now let’s try reprogramming your fingerprint using the helpful tips below.

Fingerprint TIPS!

1. Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).

2. During the 5 scan programming process for each finger, slightly repositioning your finger after each scan will store more information and increase your success rate.

3. Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

4. To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

Program the First Print

1) Open the safe. Program the 1st fingerprint by quickly pressing “PROGRAM”. The light above the fingerprint scanner will turn solid RED and the ‘1’ key on the keypad will start blinking RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the ‘1’ key lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the ‘2’ key lights up GREEN and lift. You will repeat this process until all keys (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.Still having issues? Please contact our support team via email at support@vaulteksafe.com.

1) Get the App. Download the Vaultek app from the Google Play store or Apple store. IMPORTANT: do not download the Vaultek WiFi app as that is used for WiFi models only.

2) Make sure your phone’s Bluetooth settings are set to ON, and open the Vaultek app to begin.

3) Next, create a Pattern Lock. This is an added layer of protection to safeguard your safe and prevent unauthorized access in the event your phone is misplaced. To create your pattern lock, simply drag your finger along the screen to connect at least four dots. This unique pattern will be required each time you open the app.

4) Now select your safe. After a few seconds your safe will appear in the search. You can drag the screen downwards to refresh if you are not seeing your safe listed. Select your safe, and enter your safe’s master code when prompted. This is the same code used to open the safe using the numeric keypad.

IMPORTANT: If you change your safe’s master code after pairing, the safe will no longer connect to your app, and you will be prompted to enter the new code when needed.

IMPORTANT: As a security measure, if too many incorrect master code entries are entered, your safe’s Bluetooth will disable and must be toggled ON again using the hot key sequence.

5) Finally, sync your phone – A) Press and hold keys ‘4’ and ‘5’ on your safe followed by the “PROGRAM” button together for 3 seconds to start the syncing protocol. B) When the status bar starts blinking RED you can finalize the pairing sequence from your app screen by pressing ‘OK’. The safe’s status bar will flash GREEN and beep when complete. If the status bar flashes RED with two beeps you will need to start over with step 4.

TIP: This pairing sequence offers enhanced security protection and can only be used to pair one phone to your safe. If the process is repeated with a different phone, the previous phone will be overridden and disconnected from the safe.

Remote Unlock This feature will be grayed out as a default and will need to be enabled. Refer to “Unlock feature is grayed out on the app”.

Note, Vaultek does not in any way access your personal data (including photos, locations, contacts, etc). The app requires permissions to store certain preferences such as safe settings and fingerprint ID names in the memory of your phone. It also uses the Bluetooth function of your phone for wireless communication with your safe.

Toggle Alert of Manual Unlock: If the Alert of Unlock is on, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing. To toggle Alert Unlock press and hold the ‘3’ key then “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF.

Tamper Detection: To check for tampering press and hold keys ‘2’ and ‘4’ together for 3 seconds. The ‘3’ key will glow RED to indicate tampering or GREEN to indicate no tampering. You can reset the tamper detection by opening the safe through one of the authorized entry points.

Toggle Sound: To toggle the sound ON/OFF press and hold keys ‘1’ and ‘3’ together for 3 seconds. If the ‘2’ key glows GREEN, the sound is ON; if the ‘2’ key glows RED, the sound is OFF.

Toggle Travel Mode: Save battery life by disabling the proximity sensor, fingerprint sensor, keypad, and Bluetooth features. To toggle travel mode ON/OFF press and hold keys ‘1’ ‘3’ and ‘5’ together until the safe beeps and the keys light up. If the keys glow RED and beeps, the safe is disabled; if the keys glow GREEN and beeps, the safe is operational.

View Battery Status: To check the battery level press and hold the ‘5’ key on the keypad (3 seconds). Keys from ‘1’ to ‘4’ will glow GREEN or RED to indicate the battery level. See pages 04 to 05 for more information.

If 4 keys glow green: 80%-100%

If 3 keys glow green: 60%-80%

If 2 keys glow green: 40% – 60%

If 1 key glows green: 20%-40%

If 1 key glows red: 10%-20%

If 1 key blinks red: less than 10%

Toggle Interior Light: To toggle the interior light ON/OFF press and hold the ‘1’ key for 3 seconds. With the light toggled to ON you can press the “LIGHT” button inside the safe to illuminate the light and can also adjust the interior light in the app. If the light is toggled OFF the light will be disabled.

Delete Fingerprints: To delete fingerprints press and hold keys ‘3’ and ‘5’ at the same time for 3 seconds until all keys (1-5) light up RED then enter your master code. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek® app.

Toggle Bluetooth: To toggle the Bluetooth ON/OFF press and hold keys ‘2’ and ‘5’ at the same time for 3 seconds. Keys ‘3’ and ‘4’ will glow RED indicating Bluetooth is off. To turn Bluetooth back on again, press and hold keys ‘2’ and ‘5’ at the same time for 3 seconds until all keys (1-5) light up RED, then input your safe’s master code. Keys ‘3’ and ‘4’ will glow GREEN to confirm Bluetooth is enabled. With the Bluetooth toggled ON you can perform various functions on the app. If the Bluetooth is toggled OFF all app functions will be disabled and your safe is undiscoverable.

Try the following if you are experiencing a low success rate with the fingerprint scanner.Let’s perform a soft reset of the scanner by deleting the fingerprints on the safe. Press and hold keys ‘3’ and ‘5’ at the same time for 3 seconds until all keys (1-5) light up RED then enter your master code. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek Bluetooth app. Then remove the battery and reinstall. Now let’s try reprogramming your fingerprint using the helpful tips below.

Fingerprint TIPS!

1. Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).

2. During the 5 scan programming process for each finger, slightly repositioning your finger after each scan will store more information and increase your success rate.

3. Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

4. To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

Program the First Print

1) Open the safe. Program the 1st fingerprint by quickly pressing “PROGRAM”. The light above the fingerprint scanner will turn solid RED and the ‘1’ key on the keypad will start blinking RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the ‘1’ key lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the ‘2’ key lights up GREEN and lift. You will repeat this process until all keys (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.

Still having issues? Please contact our support team via email at support@vaulteksafe.com.

VE10

Toggle Alert of Manual Unlock: If the Alert of Unlock is on, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing. To toggle Alert Unlock press and hold the ‘3’ key then “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF.

Tamper Detection: To check for tampering press and hold keys ‘2’ and ‘4’ together for 3 seconds. The ‘3’ key will glow RED to indicate tampering or GREEN to indicate no tampering. You can reset the tamper detection by opening the safe through one of the authorized entry points.

Toggle Sound: To toggle the sound ON/OFF press and hold keys ‘1’ and ‘3’ together for 3 seconds. If the ‘2’ key glows GREEN, the sound is ON; if the ‘2’ key glows RED, the sound is OFF.

Toggle Travel Mode: Save battery life by disabling the proximity sensor, fingerprint sensor, keypad, and Bluetooth features. To toggle travel mode ON/OFF press and hold keys ‘1’ ‘3’ and ‘5’ together until the safe beeps and the keys light up. If the keys glow RED and beeps, the safe is disabled; if the keys glow GREEN and beeps, the safe is operational.

View Battery Status: To check the battery level press and hold the ‘5’ key on the keypad (3 seconds). Keys from ‘1’ to ‘4’ will glow GREEN or RED to indicate the battery level. See pages 04 to 05 for more information.

If 4 keys glow green: 80%-100%

If 3 keys glow green: 60%-80%

If 2 keys glow green: 40% – 60%

If 1 key glows green: 20%-40%

If 1 key glows red: 10%-20%

If 1 key blinks red: less than 10%

Toggle Interior Light: To toggle the interior light ON/OFF press and hold the ‘1’ key for 3 seconds. With the light toggled to ON you can press the “LIGHT” button inside the safe to illuminate the light and can also adjust the interior light in the app. If the light is toggled OFF the light will be disabled.

VR10

1) Get the App. Download the Vaultek app from the Google Play store or Apple store. IMPORTANT: do not download the Vaultek WiFi app as that is used for WiFi models only.

2) Make sure your phone’s Bluetooth settings are set to ON, and open the Vaultek app to begin.

3) Next, create a Pattern Lock. This is an added layer of protection to safeguard your safe and prevent unauthorized access in the event your phone is misplaced. To create your pattern lock, simply drag your finger along the screen to connect at least four dots. This unique pattern will be required each time you open the app.

4) Now select your safe. After a few seconds your safe will appear in the search. You can drag the screen downwards to refresh if you are not seeing your safe listed. Select your safe, and enter your safe’s master code when prompted. This is the same code used to open the safe using the numeric keypad.

IMPORTANT: If you change your safe’s master code after pairing, the safe will no longer connect to your app, and you will be prompted to enter the new code when needed.

IMPORTANT: As a security measure, if too many incorrect master code entries are entered, your safe’s Bluetooth will disable and must be toggled ON again using the hot key sequence.

5) Finally, sync your phone – A) Press and hold keys ‘4’ and ‘5’ on your safe followed by the “PROGRAM” button together for 3 seconds to start the syncing protocol. B) When the status bar starts blinking RED you can finalize the pairing sequence from your app screen by pressing ‘OK’. The safe’s status bar will flash GREEN and beep when complete. If the status bar flashes RED with two beeps you will need to start over with step 4.

TIP: This pairing sequence offers enhanced security protection and can only be used to pair one phone to your safe. If the process is repeated with a different phone, the previous phone will be overridden and disconnected from the safe.

Remote Unlock This feature will be grayed out as a default and will need to be enabled. Refer to “Unlock feature is grayed out on the app”.

Note, Vaultek does not in any way access your personal data (including photos, locations, contacts, etc). The app requires permissions to store certain preferences such as safe settings and fingerprint ID names in the memory of your phone. It also uses the Bluetooth function of your phone for wireless communication with your safe.

Toggle Alert of Manual Unlock: If the Alert of Unlock is on, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing. To toggle Alert Unlock press and hold the ‘3’ key then “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF.

Tamper Detection: To check for tampering press and hold keys ‘2’ and ‘4’ together for 3 seconds. The ‘3’ key will glow RED to indicate tampering or GREEN to indicate no tampering. You can reset the tamper detection by opening the safe through one of the authorized entry points.

Toggle Sound: To toggle the sound ON/OFF press and hold keys ‘1’ and ‘3’ together for 3 seconds. If the ‘2’ key glows GREEN, the sound is ON; if the ‘2’ key glows RED, the sound is OFF.

Toggle Travel Mode: Save battery life by disabling the proximity sensor, fingerprint sensor, keypad, and Bluetooth features. To toggle travel mode ON/OFF press and hold keys ‘1’ ‘3’ and ‘5’ together until the safe beeps and the keys light up. If the keys glow RED and beeps, the safe is disabled; if the keys glow GREEN and beeps, the safe is operational.

View Battery Status: To check the battery level press and hold the ‘5’ key on the keypad (3 seconds). Keys from ‘1’ to ‘4’ will glow GREEN or RED to indicate the battery level. See pages 04 to 05 for more information.

If 4 keys glow green: 80%-100%

If 3 keys glow green: 60%-80%

If 2 keys glow green: 40% – 60%

If 1 key glows green: 20%-40%

If 1 key glows red: 10%-20%

If 1 key blinks red: less than 10%

Toggle Interior Light: To toggle the interior light ON/OFF press and hold the ‘1’ key for 3 seconds. With the light toggled to ON you can press the “LIGHT” button inside the safe to illuminate the light and can also adjust the interior light in the app. If the light is toggled OFF the light will be disabled.

Toggle Bluetooth: To toggle the Bluetooth ON/OFF press and hold keys ‘2’ and ‘5’ at the same time for 3 seconds. Keys ‘3’ and ‘4’ will glow RED indicating Bluetooth is off. To turn Bluetooth back on again, press and hold keys ‘2’ and ‘5’ at the same time for 3 seconds until all keys (1-5) light up RED, then input your safe’s master code. Keys ‘3’ and ‘4’ will glow GREEN to confirm Bluetooth is enabled. With the Bluetooth toggled ON you can perform various functions on the app. If the Bluetooth is toggled OFF all app functions will be disabled and your safe is undiscoverable.

Free Shipping

Veteran Founded

Superior Support

Price Guarantee

**NEW** VS10i

VT10i/VT10

VE10

VR10

Search

Let customers speak for us

NEW VS10i